CERRXIAN SATA Female to 40 pin Male 3.5 inch IDE Adapter for PC to SATA Hard Drive Interface Adapter

If you want to convert the external Sony enclosure for the pcmcia Japanese PS2 (10000/15000/18000) from side to sata, due to space constraints you would have to use a 2.5” laptop sata drive. This adapter uses a JMicron 20330, I was explicitly looking for it due to my application. I used this adapter inside the scph 20400 and it supported a 3tb 2.5” sata hdd no problem, so now I can enjoy my japanesePS2 scph18000. The adapter came with black foam applied to the sata side to insulate the exposed contacts from touching the metal parts of the hdd, I lifted it and applied hot glue for a much stronger adhesion and added electric tape on top to avoid the possibility of the foam getting pierced. With a 2.5” hdd it’s not much of a concern as the power stays by the side but with a 3.5” hdd (not my use case) I wanted the extra insulation. I can’t speak to longevity but for now it does what it is supposed to well.

Item as described.. installed and working..

Used this to replace the IDE hard drive in a SEGA Lindbergh Yellow. This unit works specifically because unlike some other converters you can set it to be master or slave, the Lindbergh needing the hard drive to be set to slave to function is what shines for this unit. I had some trouble with the machine wanting to use an SSD, however a spare SATA hard drive from a decommissioned PC did the trick. If I get an SSD working I will write a follow up review. I did end up adding some extra double sided tape to the back of the unit.

Helped me put a sata ssd to the old dell dimension I bad laying around

I bought this adapter as a cheaper alternative to the one I normally use. At first everything seemed fine: it connected without issues, the system recognized it immediately, and the drive worked normally. Unfortunately, after about 4 hours of use I restarted my computer and the adapter was no longer recognized. I tried reconnecting it, swapping to another adapter and then back again, but nothing helped. The same drive works perfectly on the same system when using my other adapter, so the problem is clearly this adapter. Overall, it’s inexpensive, but in my case it failed very quickly, so I can’t recommend it.

Needed 4 Sata to IDE adapters that would work in a Master/Slave setup. Tried adapters from 2 other manufactures with no success. This product solved my problem. The ones I recieved came with insulating foam tape on the side facing the drive which is a nice touch.

Before you do anything. Apply electrical tape on the other end where the IDE power connector is. They didn’t bother to protect the solder points that can cause an electrical short. Hard drives are still made of metal and this bridge can short itself on the hard drive. If you plan on restoring your Original Xbox, the only method is through modification to replace the older hard drive. This is the bridge you need to clone your Xbox onto a SATA hard drive. Just be sure to keep the file transfer slow to avoid corrupting any files during an FTP transfer. She’s old and can’t run that fast. Some of these bridges were a hit or miss in the past where the data rate seem oddly slow; in the kilobytes per second… so once you see that, try again and if it continues, replace it with a new one. Oh, and use a twin IDE power cable for powering the secondary hard drive. Keeping everything on the same electrical circuit makes it easier to do the cloning process. I used an external power supply that I used for cloning my computer which made it more annoying and difficult to deal with. Haha Good luck!!

Does the job wasn’t my fix as my problem was something else but for what it’s designed for definitely does the job so great item will keep mine and buy another should I need to!

Just for fun. It supported an M-AUDIO AP192K audio card. It ran on Windows 10 too! These audio boards offer huge dynamic range if you can use that.

This works great on my older Macs , converting to SSD'S BUT DOESN'T work with Apple XRAID SERVER

The adapter works perfect ! Using it with an 128gb sata ssd on a pentium 3 machine. I confirm this once is a gem for upgrading old systems. 5/5 stars, will buy again if i need extra adapters.

4 pin power connector somewhat tight; easy to flex the rather thin PWB while inserting; however survived my handling. Somewhat tight on 40 pin IDE connecter as well so not great if need to move it around much; fine for a fixed install. SATA connector is no problem. So far so good. It is still working.

I have an old Pentium computer that I wanted to load Windows 95 on and re-live the experience. Sadly my last IDE hard drive died and in searching for some new-old stock, I came across this adapter. It allowed me to repurpose one of SATA drives and connect it to the IDE port. I chose to use the smallest SATA drive I had (64 GB) however they all seemed to work with the only limitations being what the OS could handle. Using this adapter with and SSD HDD will give you a speed boost on your old hard drive as seek and read/write times are dropped. Very nice product.