NoCry 20V Cordless Impact Wrench - 300 ft-lb (400 Nm) Torque, 2700 Max IPM, 2200 RPM, 1/2 Inch Anvil; 4.0 Ah Battery, Fast Charger, Belt Clip & Carrying Case Included

Bought this for working on our cars/bikes, Thought it might help with some of the bolts and make it a bit quicker I had no idea just how good this Wrench is. It removes every bolt and nut we tried, Wheel nuts, Brake calipers, ball joints, drive shaft end nuts, gearbox bolts, wishbones, water pump pulley bolts etc etc etc This wrench has a lot of torque and will make short work of any job, Even if its just changing a Flat tyre it is done in seconds. Charge time is good and lasts for a few hours, enough for almost all jobs, it feels comfortable in the hand and is not heavy at all, well balanced when using it You can vary the amount of torque by squeezing the trigger softer or give it all the power by holding it down fully. Make sure you buy decent impact wrench sockets though cos this has a lot of power and ordinary sockets can shatter. This is not just for cars though, we have also used it on our bikes and garden tools, Fencing bolts and even of concrete bolts, So it is an all-round wrench for all jobs around the home and cars. I am very pleased with this wrench and would highly recommend it to everyone, it will not let you down with even the tightest of bolts and make every job easy and faster. If there was one thing i would like to see is a light to shine on the bolts from the wrench body but that's a small ask Buy it, Use it, Love it Well priced and engineered very well too 10 out of 10 for this

I was seeking to replace my 1/2" Drv Air Impact Gun with a battery cordless one. I go motor racing and need a 250ft/lb impact wrench to quickly change my racing wheels (but without the hassle of dragging a heavy air compressor around the pits, and trying to find a mains socket somewhere). Fellow competitors were using cordless guns from well known brands, costing £400 or more. I needed a tighter budget, so I was surprised to find this NoCry 20v Cordless tool for little more than a quarter of that price. The burning question was "is it any good?". When my NoCry wrench arrived, I used my Air Gun (on max 250ft/lb setting) to tighten the special centre-lock wheel nuts on my race car. I then tried to undo those nuts with this NoCry cordless gun - and was much impressed by the immediate removal of said nuts. I have now owned my NoCry gun for over a month, and have used it at 2 race events, changing wheels every bit as slick as my old Air gun did before. I have also used this 20v Cordless tool to remove propshaft bolts, 13mm seat mounting bolts, gearbox mounts, engine bellhousing bolts - and the battery still indicates it's full - amazing! The NoCry wrench came nicely presented in a sturdy kit bag which also has space to store the charger. Don't be put off by the slightly farcical brand name - this is, in my opinion, a very solid and competent piece of kit. Worth every penny, so far.

Well used it for the first time properly today. I will say it's pretty impressive for value for money. Used it to do a suspension. Brake and disc change on a 2006 Ford Focus. It stood up well to all the tasks I put it through. Some bolts were really corroded and rusted up. It handled 15/17/19/21mm nuts and bolts well. Used its several times in the workshop over the last couple of months but nothing to excessive. But today challenged it well. But there was nothing it struggled with. I will have to give it 5/5 for value for money and ease of use. I also have other brands of this item. This is not far from the top. Light weight and plenty to torque. For a home garage or workshop this is a great addition to the tool box. With a good set of impact sockets this is a great product.

With so many battery wrench’s to choose from it was difficult to find the right one in a reasonable price bracket. This wrench does as it says it’s got more than enough power to take wheel nuts off and on. It will undo hub nuts etc no problem and to top it off Raino at no cry is the most helpful efficient guy to contact. I experienced a power drop on mine and with a message on Facebook he responded straight away and sent me a brand new unit which has been perfect no power drop battery life is superb, the only negative is the smell from the motor brushes when it’s new but to be expected this has since disappeared with use. Hoping nocry will come up with a brushless wrench at some point as this would be even better. I would definitely buy from this company again as these guys offer better customer service than any brand name does.

Decent overall. Used for car and can wheel nuts. Removes most. Only struggle I've had is with over tightened wheel nuts. Overall pretty decent for the money

It is a fantastic piece of equipment, especially at the price. I have had mine now for 3 years and it has never failed to work. It is solidly built and feels sturdy from the moment you pick it up. As you would expect for the type of tool it is it has had a few knocks and bumps but you wouldn't know when you look at it. I love it and since then I have bought other items from NoCry and am equally delighted with them.

I rarely leave product reviews but in this case I'm making an exception. NoCry's impact wrench is a great bit of kit. It got undone bolts that I would normally struggle undoing with large breaker cars, and it undone them effortlessly. In addition to their great product comes excellent customer service. I had an issue and Raino from NoCry dealt with my problem extremely efficiently with no quibbles whatsoever. Which in my opinion makes for a great company and great product, and because of this service I received I will always be sure to do business with them again when I'm looking for power tools! I can't recommend them highly enough!

I had been struggling to remove the bolts from the rear bush of an Audi A6 wishbone! After having a bar on them for days I decided to buy one of these... Took the bolts out in seconds ! I did have a issue with mine however the customer services has absolutely A* and corrected the issue the next day. I could not recommend this impact gun more, the time this will save you is incredible. Wheel's come off the car so fast ! Thanks Nocry, brilliant product !

Ich muss ehrlich sagen, dass ich für den Preis sehr begeistert bin! Ich habe mir so einen kabllosen und schlauchlosen Schalgschrauber zulegen wollen seit "ChrisFix" in seinem Youtube Channel ein gerät von Milwaukee empfohlen hat. Nun, dieses Exemplar war mir für meinen Einsatzzweck doch zu Preisintensiv, weßhalb ich mich für das Gerät von NoCry entschieden habe. Vor einem Jahr fand ich dieses Angebot noch nicht, aber regelmäßiges suchen tut gut. Nun zum Produkt: Der Schlagschrauber liegt super in der Hand, ist nicht zu schwer, trotz des großen und Leistungsstarken 20v Akkus. Da bei einem Akku auch die Amperestunden ausschlaggebend sind, wie beim Auto die PS und das Drehmoment in Nm, sind 4.0 Ah in Ordnung für diese Akkus. Der Schlagschrauber selber ist schön designt und mit einem Gummischutz verkleidet der stürze aus geringer höhe abmildern sollen. Ich hab den Schrauber nicht fallen lassen weil ich mein Glück nicht herausfordern will, aber er fasst sich super an, ergonomisch, und optisch ein traum. Der Schlagschrauber hat fast mühelos die 20 Radschrauben meines Autos gelöst, welche ich mit max. 140 Nm anzuziehen pflege! Bei dreien hat er sich zwar schwer getan und musste von einen pneumatischen zu hilfe nehmen, aber der Kundensupport ist phänomenal! Mir wurde innerhalb eines Werktages Rede und Antwort gegeben. Sensationell! Aufgrund eventueller Fehler der Benutzung und eventueller Leistungseinbuße des Bürstenmotors wurde mir sehr geholfen. Ein RIESEN Dank an Raino an dieser Stelle. Man darf den Akkuschlagschrauber nicht benutzen wie einen pneumatischen Schalgschrauber, diese haben mehr als die doppelte Kraft. Des Rätsels Lösung ist den Akkuschlagschrauber länger "rattern" zu lassen. Über die Akkulaufleistung kann ich momentan nicht viel sagen, nur soviel sei gesagt: Nach 20 Radschrauben lösen und wieder anziehen war der Akku noch mit 4/4 der Ladeanzeige am Akku selber noch gefüllt. Angegeben ist der Akku ohne Last, bei dauervollgas mit 65min Laufzeit. Für den Preis den NoCry aufruft ist es für den Heimschrauber ein tolles Gerät, welches ich mit meiner jetzigen Erfahrung immerwieder kaufen würde. Auch ein Grund dafür ist der sensationelle Kundenservice!

Buena relación calidad precio, potente y buena duración de batería. Hay tornillos que no puede quitar pero es normal, incluso una pistola neumática le cuesta. Volvería a comprar

Pistola molto ben fatta, bella pesante e potente. Batteria molto buona per uso prolungato.

Buena calidad este es el segundo equipo aun que siento que a este le dura un poc omenos la bateria

I unpacked it and liked the case a lot immediately. It's exactly big enough to hold everything you'd need to fix a flat at the south pole. (And the charger.) The next thing that impressed me was the manual! No crappy English! You get the impression this was written by a guy who's been working on mechanical stuff for decades. It basically says to never store the battery discharged, by the way!! I love when they tell you how to treat the quite expensive lithium battery! Some people have been complaining about the forward | reverse switch. The company jumped on it! Their apology and corrective action almost happened before the switch problem. Very quick response. My switch, by the way, works perfectly: left - forward, center - locked, and right - reverse, just like a lot of other tools I have. Don't worry about the switch. Next thing to point out is the reviews saying it doesn't have enough power are written by people that give the impression that they are idiots. The ones saying it has plenty of power were written by people who seem to be reasonably intelligent. I am going to try to sound intelligent here, because I'm with the people who think it has a lot of power. 17 mm lug bolts on a 1982 diesel VW Rabbit: It didn't even spank them, it just instantly turned them out. | 19 mm lug nuts on a 2000 Honda Accord (Now these were put on by a tire place with an air wrench; I watched the guy do it.): It beat on them for about a second and got them off. I also put them back on using this thing, letting it pound on them for about a second. Then I went and got a breaker bar and tightened them like I normally would. The thing is, I only moved them to see how tight it got them; NOT to actually tighten them! In other words, this thing got them perfectly tight. | The injector pump sprocket on a 1992 turbo-diesel (EcoDiesel) Jetta: This is also 19 mm and it has to be tight. This thing, held for, again, about a second, tightened it perfectly, too, and I'm afraid the next poor guy who works on it is going to need exactly the right kind of puller to get that sprocket back off. Good and tight! The only worse things I would think, would be an axle shaft nut and a lawn mower blade. Sorry. I'm not gong to do that for fun. I will say that, on stuff like that, holding the whatever motionless so it doesn't just turn, is half the battle! It's like, for the riding mower blades, the way to do it would be two big, long pipes: one for the breaker bar and one slid over the blade so it can't turn. I am absolutely looking forward to doing those blade with this thing!! Should be way, way easier! Finally, this thing is very well made - the front piece is metal and the rest of it in the back is some kind of really rugged plastic. It's every bit as well-made as I would expect a Ridgid or a Dewalt or whatever to be. OK. Sigh. You want some cons to prove that I'm being honest. It doesn't have a work light on the front so you can see what you're doing without going to get your LED flashlight, OK? Happy? Oh, yea! One more! It's way too hard to review how long it runs because you'd pretty much have to do a whole bunch of stuff with it to run down the battery. I'm convinced this is the best one on Amazon for the money. _________________________________________________________________________________ Update - 9 Sept, 2021: I could not be happier with this thing!! A few days ago, I figured out what it's absolutely most useful for! Changing blades on a riding mower!! With the front of the riding mower suspended at about 45 degrees, I had tried to hold the blade from turning as I turned the opposite direction with a breaker bar with a pipe on it. Sound like fun? This time, I got the NoCry (The battery was still full after MONTHS!) and a 15/16th's short socket. This thing got the bolts (2 blades) out in way under a second each! It was as if someone had forgotten to tighten them (but I had gotten them as tight as I could; trust me!) - they came out that easy! After changing the blades, I let the NoCry tighten the bolts for about 3 or 4 seconds and I'll guarantee they're tight enough! What a difference! This time, the hardest part was suspending the front of the riding mower. I think I'd buy this thing for changing mower blades, only, if it came down to it!!