Orion Motor Tech Wheel Bearing Puller Tool Kit Compatible with Harley Davidson Motorcycles, Wheel Bearing Remover Installer Tool Set for 0.75" 1" 25mm Bearings Compatible with Hogs from 2000

Great to change wheel bearings in motorcycle wheels.

Went to swap my rear tire on my Rocker C and I noticed the bearing were kind of rachety. Really glad I pulled them they must have just started to disintegrate. How many miles you ask! 7400. Check those bearing folks.

This set is so bad I want to throw it out and not return it for it's refund to help prevent one of you from getting it, worse now because it's used. I only gave the 1 ⭐ because everyone needs a participation trophy, but I don't think this would even make a good anchor! There is no way the "5 ⭐" reviews on here are true! They were either bought or a bunch of people in an Indian call center got board and tried hyping this up. A) The instructions give you the size of the nuts and hardware included and call them out by size in the removal instructions. 1 (5/8 nut) of the 6 (3 nuts and 3 "bearing remover"s) is listed correctly. The other 2 nuts aren't only the wrong size listed, but they're not even a size (SAE or Metric) that corresponds to a known and utilized scale. 2 out of the 3 "Bearing Remover"s are so a wrench can be used to hold the "bearing remover" in place but it's manufactured so the it also is the wrong size AND not even a size (SAE or Metric) that corresponds to a known and utilized scale while the 3rd one (the one I thought might work) doesn't have any way to hold the "bearing remover" unless you breakout the good ol duct tape and cover grips. B) Being a mildly skilled motorcycle, car, truck and Navy Aircraft mechanic, I thought I could possibly work with this difficult to use tool. But 2 of the "Bearing Remover"s were clearly too small and the third which looked about right but it's either still too small or the lip of the "bearing remover" is insignificant as the "bearing remover" when tightened came right through the bearing, leaving the bearing in place. I was always told when growing up that "Good tattoos aren't cheap and cheap tattoos aren't good!" Same rule needs to be applied here. Don't waste your time or money with this.

it's a nice set but the M18 puller nut stripped out the threads after the pulling the first bearing. I knocked out the second bearing from the backside so I could finish the bearing removal job for my 2008 Harley Softail. Bought myself a quality new M18 nut for the future, please make sure you have a backup M18x1.0 puller nut handy.

Works just as well as the big name kits for a fraction of the price.

If you know how to properly work a bearing puller this will get the job done. I’m convinced some of the other reviews are from people that misused it. I have 25mm bearings on my bike and without a single issue I pulled old and installed new bearings quickly and easily. I spent less than 30 minutes on the install. Super fast. All the materials feel very well built and durable. I couldn’t find a better value for the money. Zero slip perfect fit and built to protect the finish of your wheels.

Purchased for wheel bearings on ‘24 FLTRX. Metal is soft. Threads of the puller rounded off after three bearings. Press works fine. If buying for the puller, buy a 17x1.0 (right hand) tap and die to go with it. Still cheaper than a JIMS. But it won’t last long.

Needed to change the front wheel bearing on my 2011 Fatboy. Plenty of bad reviews but this worked great removing and installing both bearings. Made sure I used plenty of oil like past reviews said. Did not see any damage so should work fine again.

Excelente

Received as appears. Prompt delivery.

Changed one set of bearings worked just fine. You will have to figure out wrench sizes as you go as the instructions seem to be wrong.

Il s’utilise parfaitement et précis

Instruction are bad (wrong wrench size). Overall quality is poor . Everything is now broken while putting the wheel bearing back on.