SainSmart USB 4 Channel DC 12V Relay Module Automation for Arduino Raspberry Pi DSP AVR PIC ARM | for Arduino Raspberry Pi DSP AVR PIC ARM

I have a virtual pinball cabinet, and I wanted to add a relay to control a fan for the "Whirlwind" game. I didn't want to spend a lot of money on this silly project. The reviews are so poor but I figured I'd risk it. There's a C# sample that Anthony Marshall provided, and it worked on this board out of the box. [...] I modified this to work in the pinball simulator's framework interface, and bam! My fan kicks on when the storm hits! I checked the other 3 relays and they work fine as well. The only negative is that the relays click a few times during boot up, apparently some issue with the FTDI chip. Sainsmart notes this in the product description on their site. Overall it's exactly what I was looking for.

The device works well, but is shipped with zero documentation. Some of the comments appear to be inaccurate. I finally got it to work with a VB.Net program I wrote. The method that worked used and FTDI supplied DotNet library and a "bit banging" mode from that library. Once written, the device works great and I have already bought more.

As others have said, the instructions and documentation really stink and the hardware has a few flaws. However, the comments on here really helped me to get this running reliably from an Android tablet. I'd like to add to the discussion to make this easier for the next person. Software: (1) You MUST set this to bitbang mode using the FTDI driver for your operating system. Specifically, for Android, I ended up passing FT_BITMODE_SYNC_BITBANG to the setBitMode method of ftDev. (See #3 below.) This cost me literally 4 hours of pulling my hair out. (2) The instruction set that Thomas Merryman posted is correct. You're writing a single byte with 0-F to the device to change the relay states. The product documentation is completely incorrect - ignore it completely. (3) To get going on android, I used a project called "Android Java D2XX". I'd put the URL, but Amazon would scrub it out. Google for the following and you should find it: "Android Java D2XX - Example projects to connect FTDI peripheral devices to an Android Host with the Java D2XX driver". For troubleshooting while getting up and running, the specific file that I modified to mess around with was DeviceUARTFragment.java, and specifically the SendMessage method. I modified that method to (1) set to bitbang mode (it is NOT in bitbang mode by default which tripped me up big time) and (2) convert the input from the app's UART screen (called writeText) to a byte (rather than a byte representation of a string of ascii chars). Then you can install the app on your Android device and use the UART GUI to write 0-15 and see the corresponding relay state changes. Hardware: (1) The circuit does not dissipate the voltage transient from opening a relay on a high inductance device (like a high power solenoid ... which I am using). You can overcome this by soldering on a freewheeling diode for each relay. Turn the board over - solder diodes from the "outer" pins surrounding the u-shaped holes. The diodes direction matters - it should point towards the USB port. (2) You can power the relays from the USB port by adding a jumper wire. Connect one end of the wire to the VCC terminal block then push the other end of the wire through the hole labeled 5V (just under R10), turn the board over and solder in place.

I've spent an entire day trying to get this to work attached to a machine running Linux. The "documentation" consists of: A short word document consisting mostly of screen captures of a windows utility to turn the relays on or off. A jpeg with the same information about baud and hex codes as on the Amazon description page. You would think that you could just fire up a terminal program and write the hex values to the serial port. For that matter: echo -en '\xFF\x01\x01' > /dev/ttyUSB0 Should work if the baud rate is correct. They also include several datasheets for the FTDI on which this is based. This chip has thousands of different applications so parsing out what if anything applies to this application is difficult. If you look hard enough there's a wiki page for this product: [...] It mentions software code examples for several languages, but doesn't have any. Here's a more convenient link for the "documentation" frmo the wiki page. [...] Aside from cheap terminal blocks with non-captive screws, the rest of the hardware looks solid enough. I'd give it several more stars if I could get it to work.

Product is just what was ordered.

Step one download the VCP (Virtual Comm Port) driver from (xxx).ftdichip.com/Drivers/VCP.htm. After installing driver, plug in the usb cable and the board will be identified as a comm port. Use device manager to determine comm port #. Open comm port at 9600 baud, 8 bit, no parity, 1 stop bit no flow control. Mr. Merryman was correct in his command determination. The relays are selected by binary where: 0001 = relay 1 on = Dec 1 0010 = relay 2 on = Dec 2 0100 = relay 3 on = Dec 4 1000 = relay 4 on = Dec 8 Let relayvalue = decimal value of relay desired ie: relayvalue = 1 for relay one. Then send chr$(relayvalue) to the comm port. If you want multiple relays add their decimal values together, 1 & 4 would be relayvalue=9 To then turn relay 4 off, subtract 8 from relayvalue and send relayvalue=1, turning off relay 4 and leaving relay 1 on. Once this was done and I found an old 5 volt dc wallwart from a discarded switch this board works great. Pity the documentation is lacking.

It works fine but I would not risk installing the software on a machine. It works best using the direct drivers and not treating in as a COMM port. Here is an example of code in XOJO (REAL BASIC). I put the FTD2XX.DLL in the directory with the project as well as installing it on my machine. You will have to get the equivalent library for android or linux. iOS you're on your own. Avoid unverified drivers. You can get them direct from ftdi for safety This code is for 4 channel relay card so higher bits are masked with true. const FT_OK = 0 const FT_DeviceIndex = 0 // need logic to select correct USBdevice const bAll_ON = &b11111111 const bAll_OFF =&b11110000 // for 4 relay board const bRelay1_3ON2_4OFF =&b11110101 // for 4 relay board dim strDescription as string dim ftStatus as int32 dim lngHandle as int32 dim lngBytesSent as int32 dim databyte as int8 Soft Declare Function FT_Open Lib "FTD2XX.DLL" (ByVal intDeviceNumber As Int32, ByRef lngHandle As Int32) As Int32 Soft Declare Function FT_Close Lib "FTD2XX.DLL" (ByVal lngHandle As Int32) As Int32 Soft Declare Function FT_SetBitMode Lib "FTD2XX.DLL" (ByVal lngHandle As Int32, ByVal bMask As Int8, ByVal bOn As Int8) As Int32 Soft Declare Function FT_Write Lib "FTD2XX.DLL" (ByVal lngHandle As Int32, ByRef bData As Int8, ByVal lngSize As Int32 ,ByRef lngBytesout As Int32) As Int32 databyte=bALL_ON ftStatus=FT_Open(0,lngHandle) if ftStatus=FT_OK then ftStatus=FT_SetBitMode(lngHandle,255,1) if ftStatus=FT_OK then ftStatus=FT_Write(lngHandle,databyte,1,lngBytesSent) end if ftStatus=FT_Close(lngHandle) else end if

Awesome

Everything was as described. Great product for the price.