Duronic Monitor Arm Single DM351X3 BK Height Adjustable Desk Mount for 13–27" Screens, VESA 75/100, 10kg Load – Monitor Riser Clamp for Home Office, Work, Gaming

It arrived within two days, and took no more than about 5 mins to install. Duronics really have put some design effort into this. Even the packaging's been thought through. The arm and mount are kept apart within the box, presumably so that they don't mark each other in transit. It comes with a selection of screws and spacers to accommodate most monitors and, with the monitor mounted, the screen is absolutely solid while still allowing you to adjust the horizontal and vertical tilt by hand. Although it comes with a height-setting clamp, the arm alone can be held tentatively in place by twisting a thumbscrew at the rear of the base of the arm (the bit that slides up/down the vertical mount), thereby allowing you to move the monitor up and down with greater freedom. Of course, if you move the monitor arm left and right, the arm gradually will slide down. More likely, you'll fit the supplied clamp, set the arm to the required height, then lift the clamp up to meet it. Even the clamp has a neat design; the mini-lever that does the tightening is like a sprung ring-spanner. It can be pulled out slightly so that it can be moved to a more suitable position on the nut so that it doesn't get in the way of the arm. It's a quality item all over, and I bought another immediately. Of course, the benefit of having two single-monitor mounts rather than a single dual-monitor mount is that you can adjust the monitor positions independently, and I should imagine the monitor stability would be greater due to the shorter arm. Worth mentioning that the VESA plate didn't fit into the recess on my primary screen, and the supplied spacers were approx 4 mm too short for the extra-length screws, so I had to extend the spacers with some washers of my own. Best 40-odd quid (for the pair) I've spent in a while, and nice to get rid of the space-occupying dust-collecting bases. The box contains also a piece of sticky-back rubber that you can attach to the inner face of the desk clamp, presumably for better friction, but I've not used it. Also included is a pack of three strips of velcro for arm cable management. Suddenly, my cluttered 'computer desk' has become a spacious writing desk with two monitors floating exactly where I want them to be. Thanks Duronics. Should have bought these years ago.

I opted for two of the DM351X3 model (as apposed to the duel DM352 version) due to the size of my monitors (27" BenQ) and the need to position them in a varied combination of landscape and portrait modes. Each desk mount was packaged very well with provided hex/Allen key and a variety of screws for the VESA mount. The addition of a sticky rubber pad for the clamp is a welcome addition and provides some welcome protection to the underside surface that you're securing the mount to. Both the 3 point arm and support pole are exceptionally strong and durable with zero bend or movement when handling such a large monitor. The cable clips help to keep everything tidy whilst the inclusion of the Duronic logo at the base of the support pole makes this desk mount look even more premium - definitely worth the £20 price tag. There are a few marginal blemishes/bubbles/bumps on the base clamp that I only noticed when taking the photos for this review - ultimately they are barely noticeably to the naked eye (due to the DM351X3 being black in color) and don't visibly detract from the visual quality of this product whatsoever! There are only two minor negatives to this product (and this is me just nitpicking); 1) horizontal and tilt positioning is excellent however to alter the height of the monitor attached you physically have to release the appropriate clamp and carefully move the 3 point arm up and down the pole support - if you're planning on changing the height of your monitors on a regular basis this could be a little annoying. 2) positioning the height of each arm (when you have 2 or more) at exactly the same height is rather tricky - the addition of some line markers/notches down one edge of the main support pole would be beneficial. At £20 you can't go wrong- these are an absolute bargain and have a truly premium feel to them!

I have two of these both holding a Dell U2412M monitor up. Having used the much more expensive Hernan-Miler and Dell versions professionally I was semi sceptical that something that is so much cheaper (1/8th of the Hernan-Miller ones) could be brilliant. However how wrong was I! It is a fantastic little product. Strong and simple to assemble, you simply slide the arm on the pole, tighten and job done! The hand tightened clamp is simple and effective, you only require a screwdriver to tighten the VESA mount to the monitor. I thought these (Single Arm) were so fab i ended up buying the second one for another monitor without a doubt in my mind. I have recommended to the professional people i work with just how brilliant these are and for such a cheap price. Do not be put off by the price, these are a brilliant product and very fit for purpose, the simplicity is brilliant and makes fitting it a 3minute job, the cable tidies work well, and the range of movement is good. Highly recommend!

My third one of these. Still an excellent product at a great price, but a couple of niggles this time, so I've taken off a star. First, the plate that attaches to the monitor was a fraction too big for the recessed section in my LG 27UL850-W monitor, so it wouldn't fit. I used a grinding wheel to remove about 1 mm from each edge of the plate, and all is fine. The issue is just as likely to be LG's fault as Duronic's, but I reckon LG calls the shots here. Second, the fore-and-aft tilt mechanism didn't work at first because the screw attaching the arm to the domed section of the steel monitor plate was done up too tight. Again this was easily fixed, but check it before you begin the assembly. To reach the screw in question you need to dismantle the joint behind it, which is a pain if you've already hung the monitor. ----------------- Updated 2018-01-02: I've just bought my second one of these. Same excellent quality, and I'm pretty sure the price has not increased. Thoroughly recommended. ----------------- This is an excellent product at a very reasonable price. I bought mine after acquiring a 21-in. monitor to use as a second screen alongside my existing 24-in. monitor. The new monitor lacked a stand, and in any case I wanted to use it in portrait mode. I'd never used a desk clamp for a job like this, and I've had one or two bad experiences with clamp-on desk lamps, but I needn't have worried – this clamp is extremely secure. The support as a whole provides all the reach you'd need for mounting on a standard office desk. It's easy to set up and adjust, sturdy, but with easy movement when needed. And if you work with documents, to try a second screen in vertical mode – it's made all the difference to my work setup.

I purchased this mount to give myself more surface space when downsizing my desk (into a smaller office). The item was sent immediately and I received it via a decent courier the following day. The item is well packaged and comes with the clamp/upright, height clamp, monitor mount, all the hardware you need (different size screws/spacers for the different monitors/mount types), a rubber pad to protect the desk surface and some telco cable ties. All the components are really sturdy and well made and everything went together as expected. When it came to setting the clamp up I found that the ball pivot joint was slightly loose for my monitor weight (a 23" Samsung screen) so the screen had a tendency to droop, especially if you banged the desk. To remedy this I just removed the screen, dismantled the main mount and then tightened up the bolt in the pivot to give it more resistance. This was easier said than done as the ball part of it move as you tighten so you need to find a way to clamp it down without damaging it (I used my DIY workbench and an allen key to hold it). The screen now sits perfectly where you leave it but allows just enough movement to reposition as required. All in all I'm very happy with the purchase and now have my complete desk area available with my monitor securely and flexibly held above it.

Ordered this and received the next working day. Very easy to set up and absolutely rock solid in place. Comes with a small rubber adhesive pad that attaches to the clamp and protects your desktop. Simply put the clamp in place and tighten up. Put on the collar and secure at a suitable height and then slide the arm onto the pole. It's easier to mount the arm to the back of the monitor in advance before sliding onto the pole. Included in the package are short and long VESA compatible bolts and spacers to cover the middle ground between the two sizes. The mount itself is compatible with VESA 75 and 100. The arm itself is easy to articulate but stiff enough to remain secure in place with no wobble for the monitor. There is an included allen key to alter the tension of the hinges if you need things tighter or to swing a little more freely. The mount can also be angled up or down a little to assist with viewing angles. You can also easily rotate the monitor 90 degrees if you want to work with portrait orientation. The arm features cable loops to keep your cabling tidy and there are also three quality velcro style cable ties to further augment this if required. I've been very impressed with the quality and contents for the money and I wish I had bought this years ago.

Duronic DM351X3 Single LCD LED Desk Mount Arm Monitor Stand Bracket with Tilt & Swivel (Tilt ±15°|Swivel 180°|Rotate 360°) + 10 Year Warranty Bought this so that I could move my small second monitor closer without it taking up space on my mouse mat. This is a really solid monitor stand (which I don't think I was expecting for the price) and it's really easy to assemble. Attaching the pole to the desk was simple and it even has a rubber sticker for the clamp so you don't scratch/mark your desktop. Once the pole was in place it was easy to attach the arm to the monitor and then slide it on to the height I wanted. The arm has little hooks for feeding the cables through and they also supply 3 velcro strips for securing the cables (haven't used these yet as I'm still moving stuff about). Adjusting the monitor on the arm feels nice and solid, not too stiff or too loose, and I was able to tilt and angle it as I wanted. All in all a great monitor arm that will get you more space on your desk and feels like it will last for ages! I'm tempted to buy a 3rd monitor so that I can get another one of these stands :)

Very impressed with the build quality and finish, and the flexible design. Even when you add in the delivery cost, it's still great value. I went for the DM35 series over the DM25 series so that I could be sure to fold the arms back on themselves, and this means the monitor goes right back almost flush with the pole. It was easy to mount, with clear instructions, and the various locking bolts come preset at a perfect balance between mobility and sturdiness, so I didn't even need to break out the allen key. The cable management guides are simple yet effective, and the flexibility of positioning is excellent. My only concern now is whether my desk is too flimsy to take the strain, but that shows how well this mount transfers the forces down to the desk, and is the fault of my desk not this product.

Robusto ben fatto, dopo qualche mese nessun cedimento. Volevo prenderne uno grigio che si abbinasse meglio al contesto in cui si trova, colori stanza, scrivania, pannello muro ecc ecc..

C'est rare que je puisse me dire que j'ai réussi un achat parfait. Vraiment. Mais là, OK, j'ai réussi l'achat parfait, à seulement 35 euros. Première surprise, toutes les pièces sont très bien finies, ce n'est pas de la camelote, bien au contraire. Tout s'emboite bien, coulisse très bien, permet une fixation solide et qui fait confiance. Tous les détails ont été bien pensés, jusqu'à la course des cables qui est gérée afin de permettre les pivotements et basculements de l'écran sans tirer les prises. Le montage se fait sans grande difficulté, et une fois installé, on n'envisage clairement pas de remettre le pied de l'écran. Je l'utilise depuis plusieurs mois, et je n'ai vraiment rien à redire. Si votre écran a des fixations VESA, foncez. 100%

Güzel ürün duvarınızı çizmelerine dikkat edin

Je suis ravi d'avoir choisi le support mural Duronic DM351X2 pour mon espace de travail ! Sa conception robuste et son installation facile en font un choix parfait. J'adore la possibilité de régler l'angle et la hauteur, ce qui me permet de travailler confortablement pendant des heures. En plus, il offre un look moderne qui complète parfaitement mon bureau. Ce support a vraiment transformé mon expérience de travail en libérant de l'espace et en rendant mon écran plus accessible. Je le recommande à tous ceux qui veulent améliorer leur setup ! 💻✨

Bonjour, J'ai acheté deux supports d'écran pour fixer mes enceintes Kef Q100: http://amzn.to/2IGigu0 L'enceinte fait 5,9kg et le support l'a accepté sans sourciller, malheureusement, ce n'est pas le cas de mon bureau que j'ai du renforcer avec une cale en bois (merci Ikea). Le système de pince est très pratique et les attaches câbles fournis sont appréciables. Ce commentaire vous a-t-il été utile ? Faites-le-moi savoir en cliquant sur OUI !